The Workings of a Water Turbine

Currently we are still using the basic desgins from Francis and other past scientists. Over the last few decades hydroelectric power stations have not been built. This is because in the lower 48s  the best and largest locations have already been tapped into. It is estimated that 75 percent of the potential water power of the U.S. is already being used up. Alaska though is quite different. less than 1 percent of the estimated 167 million kilowatts available in Alaska has been harnessed to date[7].

How Water Turbines Work

Water turbines rely on simple principles of physics. The turbines use waters high flowing energy to turn a blade that is connected to the shaft of a generator to generate electricity. The figure above gives a basic understanding of the parts of a hydropower plant.

Courtesy of http://science.howstuffworks.com/environmental/energy/hydropower-plant1.htm

Dam- This part of the hydroplant holds back the reservoir and contains massive amounts of potential energy.

Intake-  Hydrostatic pressure pulls the water through the penstock. The penstock is a pipeline that leads to the turbine. A penstock is what controls the rate and volume of water flow from a water source towards a hydro turbine generator.  It is usually designed as a closed pipe with opening and closing gates to allow only the desired amount of water into the system[5].

Turbine- The water rushes in and strikes the large blade of the turbine which is attached to a generator above by a shaft. The most common type of turbine for hydoplants is a Francis turbine. These turbines can weigh as much as 172 tons and turn at a rate of 90 revolutions per minute.  Francis turbines are most used because they are able to operate efficiently even with large changes in flow rates. The blades of the Francis turbine are shaped precisely to provide lift. When water flows over the blades, a low pressure will be induced on one side, and high pressure on the other side. This will result in a lift force. The blades also get another help with rotation, and that is the impulsive force due to the bucket shape towards the outlet. As you can see Newton’s third law is being used extensively here. A spiral casing is used on the Francis turbines to maximize flow energy. When power needs vary the Francis turbines are equipped with guide vanes to control flow rates and flow angle[5][6].

Image courtesy of http://www.learnengineering.org/2014/01/how-does-francis-turbine-work.html

Here is a link to a good video on Francis Turbines: http://www.youtube.com/watch?v=3BCiFeykRzo

Generator- As you should know from class, their are a series of magnets are turning inside the generator as the turbine blades turn. These giant magnets rotate past the copper coils to produce alternating current.

Transformers- Inside the power plant is a transformer that steps up the voltage. Stepping up this generated voltage depends on the number of turns on the secondary coil. A step-up transformer can raise the voltage by several hundred thousands volts.
,
Image courtesy of www.mekanizmalar.com


Important Factors for Hydro-Power

Now that you have learned the many parts a hydoplant, lets look at some key factors to maximize power generation.

Power = Gravity*Water Flow Rate*Head Height

We are familiar with gravity of course,but not flow rate and head height. The hydraulic head is the distance that water flows from the higher elevation where it is stored, to the hydro-turbine generator. Hydraulic head is usually divided into three categories: low, medium, and high head.
Elevations above around 100 meters are usually considered high head, while low head system elevations range around 10 meters in height. A high head hydro turbine system requires less volume of water flow to operate because the momentum collected from gravity through the longer distance of falling water makes up for the loss of volume.
The high head systems also require a smaller turbine because of the lower volume of water flow needed.
A low head hydro turbine is usually used in a flowing river with little elevation change, or in moving ocean tides.
A low head system with a high volume of water usually requires a much larger turbine generator to efficiently convert the water energy into electricity[8].


Environmental Impacts

Although hydroelectric power is much cleaner compared to fossil fuel, it still poses risks to the environment. A dam can seriously alter the ecosystem near it. Dams have been known to help kill off fish species, because it is very difficult for them to migrate upstream even with a fish ladder installed. When the height of the water reservoir changes, it impacts the plants and animals that depend on that water[8].






Valid
              XHTML 1.0 Strict